百鷹BY-9800B無線打印吊秤標定方法
上海百鷹電子吊秤有直視吊鉤秤、耐高溫吊秤、無線打印吊秤、手持式電子吊秤等四種;
電子吊秤量程:
直視吊秤(量程) | 無線數傳帶打印吊秤(量程) |
100kg、200kg |
|
300kg |
|
500kg | 3噸(3t) |
1噸(1t) | 5噸(5t) |
2噸(2t) | 10噸(10t) |
3噸(3t) | 15噸(15t) |
5噸(5t) | 20噸(20t) |
10噸(10t) | 30噸(30t) |
15噸(15t) | 40噸(40t) |
20噸(20t) | 50噸(50t) |
30噸(30t) | 可定制:60噸、80噸、100噸無線吊秤 |
BY-9800B無線打印儀表吊秤操作方法:
1按”目/C”鍵, 顯示“參數設置“界面。
2按2系統設置, 顯示請輸入密碼“000000”。
3輸入密碼6個“111111”,按“確認”鍵,顯示“系統設置“。
4按”1”系統標定, 顯示系統標定界面,注意1-3號參數請不要按。
5空秤時,按“4”鍵,零位確認,確認成功顯示“完成”。
6掛起砝碼,等5秒鐘,穩定后,按“5”鍵,然后輸入“砝碼值”(如100kg就按“100”),按“確認”鍵。
7按“目/C”鍵3次,退回稱量界面,就會顯示砝碼分量。
百鷹BY-9800B無線打印吊秤標定方法
BY9800-B calibration manual
1 press the "目/C" button to display the "parameter setting" interface.
2 Press 2 system settings, display the password "000000"".
3 enter six password "111111", press "confirm" button, display "system settings".
4 Press "1" system calibration, display system calibration interface, note that the 1-3 number parameters, please do not press.
5 when empty scale, press the "4" key, Zero to confirm, confirm success and showing “finish”.
6 hang up the weight, wait for 5 seconds, after the stability, press "5" key, and then enter "weight value" (press “100” if it is 100kg), press "confirm".
7 press the "目/C" button 3 times, return to the weighing interface, it will show the weight component.
百鷹BY-9800B無線打印吊秤標定方法
掃一掃 微信咨詢
©2024 天津沐恒稱重設備科技有限公司 版權所有 備案號: 技術支持: GoogleSitemap 總訪問量:385640